Skip to main content

nw commands


troubleshoot commands in Linux.

 

1. ifconfig

ifconfig (interface configurator) command 
 is use to initialize an interface, assign IP 
Address to interface and enable or disable
 interface on demand. With this command 
you can view IP Address and Hardware / MAC 
 address assign to interface and also MTU (Maximum transmission unit) size.
# ifconfig
 
eth0      Link encap:EthernetHWaddr 00:0C:29:28:FD:4C
inet addr:192.168.50.2  Bcast:192.168.50.255  Mask:255.255.255.0
          inet6 addr: fe80::20c:29ff:fe28:fd4c/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:6093 errors:0 dropped:0 overruns:0 frame:0
          TX packets:4824 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:6125302 (5.8 MiB)  TX bytes:536966 (524.3 KiB)
          Interrupt:18 Base address:0x2000
 
lo        Link encap:Local Loopback
inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:480 (480.0 b)  TX bytes:480 (480.0 b)
ifconfig with interface (eth0) command 
 only shows specific interface details like 
IP Address, MAC Address etc. with -a options 
will display all available interface details if it 
 is disable also.
# ifconfig eth0
 
eth0      Link encap:EthernetHWaddr 00:0C:29:28:FD:4C
inet addr:192.168.50.2  Bcast:192.168.50.255  Mask:255.255.255.0
          inet6 addr: fe80::20c:29ff:fe28:fd4c/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:6119 errors:0 dropped:0 overruns:0 frame:0
          TX packets:4841 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:6127464 (5.8 MiB)  TX bytes:539648 (527.0 KiB)
          Interrupt:18 Base address:0x2000

Assigning IP Address and Gateway

Assigning an IP Address and Gateway 
to interface on the fly. The setting will
 be removed in case of system reboot.
# ifconfig eth0 192.168.50.5 netmask 255.255.255.0

Enable or Disable Specific Interface

To enable or disable specific Interface, 
we use example command as follows.
Enable eth0
# ifup eth0
Disable eth0
# ifdown eth0

Setting MTU Size

By default MTU size is 1500. We can
 set required MTU size with below 
command. Replace XXXX with size.
# ifconfig eth0 mtu XXXX

Set Interface in Promiscuous mode

Network interface only received packets 
 belongs to that particular NIC. If you put
 interface in promiscuous mode it will received 
all the packets. This is very useful to capture 
packets and analyze later. For this you may 
require superuser access.
# ifconfig eth0 - promisc

 

2. PING Command

PING (Packet INternet Groper) command
 is the best way to test connectivity between two 
nodes. Whether it is Local Area Network (LAN) or 
Wide Area Network (WAN). Ping use ICMP 
(Internet Control Message Protocol) to communicate
 to other devices. You can ping host name of ip address 
using below command.
# ping 4.2.2.2
 
PING 4.2.2.2 (4.2.2.2) 56(84) bytes of data.
64 bytes from 4.2.2.2: icmp_seq=1 ttl=44 time=203 ms
64 bytes from 4.2.2.2: icmp_seq=2 ttl=44 time=201 ms
64 bytes from 4.2.2.2: icmp_seq=3 ttl=44 time=201 ms
 
OR
 
# ping www.tecmint.com
 
PING tecmint.com (50.116.66.136) 56(84) bytes of data.
64 bytes from 50.116.66.136: icmp_seq=1 ttl=47 time=284 ms
64 bytes from 50.116.66.136: icmp_seq=2 ttl=47 time=287 ms
64 bytes from 50.116.66.136: icmp_seq=3 ttl=47 time=285 ms
In Linux ping command keep executing until 
you interrupt. Ping with -c option exit after N
 number of request (success or error respond).
# ping -c 5 www.tecmint.com
 
PING tecmint.com (50.116.66.136) 56(84) bytes of data.
64 bytes from 50.116.66.136: icmp_seq=1 ttl=47 time=285 ms
64 bytes from 50.116.66.136: icmp_seq=2 ttl=47 time=285 ms
64 bytes from 50.116.66.136: icmp_seq=3 ttl=47 time=285 ms
64 bytes from 50.116.66.136: icmp_seq=4 ttl=47 time=285 ms
64 bytes from 50.116.66.136: icmp_seq=5 ttl=47 time=285 ms
 
--- tecmint.com ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 4295ms
rtt min/avg/max/mdev = 285.062/285.324/285.406/0.599 ms

 

3. TRACEROUTE Command

traceroute is a network troubleshooting utility
 which shows number of hops taken to reach 
destination also determine packets traveling path. 
Below we are tracing route to global DNS server IP 
Address and able to reach destination also shows path
 of that packet is traveling.
# traceroute 4.2.2.2
 
traceroute to 4.2.2.2 (4.2.2.2), 30 hops max, 60 byte packets
 1  192.168.50.1 (192.168.50.1)  0.217 ms  0.624 ms  0.133 ms
 2  227.18.106.27.mysipl.com (27.106.18.227)  2.343 ms  1.910 ms  1.799 ms
 3  221-231-119-111.mysipl.com (111.119.231.221)  4.334 ms  4.001 ms  5.619 ms
 4  10.0.0.5 (10.0.0.5)  5.386 ms  6.490 ms  6.224 ms
 5  gi0-0-0.dgw1.bom2.pacific.net.in (203.123.129.25)  7.798 ms  7.614 ms  7.378 ms
 6  115.113.165.49.static-mumbai.vsnl.net.in (115.113.165.49)  10.852 ms  5.389 ms  4.322 ms
 7  ix-0-100.tcore1.MLV-Mumbai.as6453.net (180.87.38.5)  5.836 ms  5.590 ms  5.503 ms
 8  if-9-5.tcore1.WYN-Marseille.as6453.net (80.231.217.17)  216.909 ms  198.864 ms  201.737 ms
 9  if-2-2.tcore2.WYN-Marseille.as6453.net (80.231.217.2)  203.305 ms  203.141 ms  202.888 ms
10  if-5-2.tcore1.WV6-Madrid.as6453.net (80.231.200.6)  200.552 ms  202.463 ms  202.222 ms
11  if-8-2.tcore2.SV8-Highbridge.as6453.net (80.231.91.26)  205.446 ms  215.885 ms  202.867 ms
12  if-2-2.tcore1.SV8-Highbridge.as6453.net (80.231.139.2)  202.675 ms  201.540 ms  203.972 ms
13  if-6-2.tcore1.NJY-Newark.as6453.net (80.231.138.18)  203.732 ms  203.496 ms  202.951 ms
14  if-2-2.tcore2.NJY-Newark.as6453.net (66.198.70.2)  203.858 ms  203.373 ms  203.208 ms
15  66.198.111.26 (66.198.111.26)  201.093 ms 63.243.128.25 (63.243.128.25)  206.597 ms 66.198.111.26 (66.198.111.26)  204.178 ms
16  ae9.edge1.NewYork.Level3.net (4.68.62.185)  205.960 ms  205.740 ms  205.487 ms
17  vlan51.ebr1.NewYork2.Level3.net (4.69.138.222)  203.867 ms vlan52.ebr2.NewYork2.Level3.net (4.69.138.254)  202.850 ms vlan51.ebr1.NewYork2.Level3.net (4.69.138.222)  202.351 ms
18  ae-6-6.ebr2.NewYork1.Level3.net (4.69.141.21)  201.771 ms  201.185 ms  201.120 ms
19  ae-81-81.csw3.NewYork1.Level3.net (4.69.134.74)  202.407 ms  201.479 ms ae-92-92.csw4.NewYork1.Level3.net (4.69.148.46)  208.145 ms
20  ae-2-70.edge2.NewYork1.Level3.net (4.69.155.80)  200.572 ms ae-4-90.edge2.NewYork1.Level3.net (4.69.155.208)  200.402 ms ae-1-60.edge2.NewYork1.Level3.net (4.69.155.16)  203.573 ms
21  b.resolvers.Level3.net (4.2.2.2)  199.725 ms  199.190 ms  202.488 ms

 

4. NETSTAT Command

Netstat (Network Statistic) command display 
connection info, routing table information etc. 
To displays routing table information use option as -r.
# netstat -r
 
Kernel IP routing table
Destination     Gateway         Genmask         Flags   MSS Window  irttIface
192.168.50.0    *               255.255.255.0   U         0 0          0 eth0
link-local      *               255.255.0.0     U         0 0          0 eth0
default         192.168.50.1    0.0.0.0         UG        0 0          0 eth0

 

5. DIG Command

Dig (domain information groper) query DNS related
 information like A Record, CNAME, MX Record etc. This command mainly use to troubleshoot DNS related query.
# dig www.tecmint.com; <<>>DiG 9.8.2rc1-RedHat-9.8.2-0.10.rc1.el6 <<>> www.tecmint.com
;; global options: +cmd
;; Got answer:
;; ->>HEADER<

 

6. NSLOOKUP Command

nslookup command also use to find out DNS related query. The following examples shows A Record (IP Address) of tecmint.com.
# nslookup www.tecmint.com
Server:         4.2.2.2
Address:        4.2.2.2#53
 
Non-authoritative answer:
www.tecmint.com canonical name = tecmint.com.
Name:   tecmint.com
Address: 50.116.66.136

 

7. ROUTE Command

route command also shows and manipulate ip routing table. To see default routing table in Linux, type the following command.
# route
 
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.50.0    *               255.255.255.0   U     0      0        0 eth0
link-local      *               255.255.0.0     U     1002   0        0 eth0
default         192.168.50.1    0.0.0.0         UG    0      0        0 eth0
Adding, deleting routes and default Gateway with following commands.
Route Adding
# route add -net 10.10.10.0/24 gw 192.168.0.1
Route Deleting
# route del -net 10.10.10.0/24 gw 192.168.0.1
Adding default Gateway
# route add default gw 192.168.0.1

 

8. HOST Command

host command to find name to IP or IP to name in IPv4 or IPv6 and also query DNS records.
# host www.google.com
 
www.google.com has address 173.194.38.180
www.google.com has address 173.194.38.176
www.google.com has address 173.194.38.177
www.google.com has address 173.194.38.178
www.google.com has address 173.194.38.179
www.google.com has IPv6 address 2404:6800:4003:802::1014
Using -t option we can find out DNS Resource Records like CNAME, NS, MX, SOA etc.
# host -t CNAME www.redhat.com
 
www.redhat.com is an alias for wildcard.redhat.com.edgekey.net.

 

9. ARP Command

ARP (Address Resolution Protocol) is useful to view / add the contents of the kernel’s ARP tables. To see default table use the command as.
# arp -e
 
Address                  HWtypeHWaddress           Flags Mask            Iface
192.168.50.1             ether   00:50:56:c0:00:08   C                     eth0

 

10. ETHTOOL Command

ethtool is a replacement of mii-tool. It is to view, setting speed and duplex of your Network Interface Card (NIC). You can set duplex permanently in /etc/sysconfig/network-scripts/ifcfg-eth0 with ETHTOOL_OPTS variable.
# ethtool eth0
 
Settings for eth0:
        Current message level: 0x00000007 (7)
        Link detected: yes

11. IWCONFIG Command

iwconfig command in Linux is use to configure a wireless network interface. You can see and set the basic Wi-Fi details like SSID channel and encryption. You can refer man page of iwconfig to know more.
# iwconfig [interface]

 

12. HOSTNAME Command

hostname is to identify in a network. Execute hostname command to see the hostname of your box. You can set hostname permanently in /etc/sysconfig/network. Need to reboot box once set a proper hostname.
# hostname
 
tecmint.com

 

13. GUI tool system-config-network

Type system-config-network in command prompt to configure network setting and you will get nice Graphical User Interface (GUI) which may also use to configure IP Address, Gateway, DNS etc. as shown below image.
# system-config-network

Comments

  1. SOL Technologies Solutions7 October 2021 at 23:09

    Thanks for this blog. I have found some interesting blogs on google. You can check these blogs also which are related to technologies….

    Job Oriented Linux Training Institute in Delhi, NCR
    Job Oriented AWS Training Institute in Delhi, NCR

    ReplyDelete
  2. SOL Technologies Solutions22 October 2021 at 05:37

    I have read all the comments and suggestions posted by the visitors for this article are very fine, We will wait for your next article so only. Thanks!

    Best Institute for AutoCAD Training Course in Delhi, NCR
    Certified JAVA Training Institute in Delhi with Placement

    ReplyDelete
  3. SOL Technologies Solutions24 October 2021 at 01:09

    The article was up to the point and described the information very effectively. Thanks to blog author for wonderful and informative post.

    Online Base-Advanced Python Training Institute in Delhi, NCR
    Online & Classroom Advanced Excel Training Course in Delhi, NCR

    ReplyDelete

Post a Comment

Popular posts from this blog

sed

Sed Command in Linux/Unix with examples SED command in UNIX is stands for stream editor and it can perform lot’s of function on file like, searching, find and replace, insertion or deletion. Though most common use of SED command in UNIX is for substitution or for find and replace. By using SED you can edit files even without opening it, which is much quicker way to find and replace something in file, than first opening that file in VI Editor and then changing it. o     SED is a powerful text stream editor. Can do insertion, deletion, search and replace(substitution). o     SED command in unix supports regular expression which allows it perform complex pattern matching. Syntax: sed OPTIONS... [SCRIPT] [INPUTFILE...] Example: Consider the below text file as an input. $cat > geekfile.txt unix is great os. unix is opensource. unix is free os. learn operating system. unixlinux which one you choose. unix is easy to learn.unix ...
Post a Comment
Read more

initramfs" file is deleted or corrupted on your RHEL or CentOS 7

Initrd/Initramfs image provides the capability to load a RAM disk by the boot loader. This RAM disk can then be mounted as the root filesystem and programs can be run from it. Afterwards, a new root file system can be mounted from a different device. The previous root filesystem which was mounted from initrd/initramfs is then moved to a directory and can be subsequently unmounted. Their are chances that either you might have accidentally deleted "initramfs" file from the /boot partition or it is corrupted due to some reason.  Then boot process will get interrupted and you will see below error: error: file '/initramfs-3.10.0-957.el7.x86_64.img' not found. Good news is you can still recover this "initramfs" by following below steps: Step 1 :  Mount RHEL or CentOS 7 ISO image on your physical server and boot from it. In case you are using HPE Prolient server you can mount this ISO image on iLO, if this is virtual environment then mount it accordingly and reboot...
Post a Comment
Read more
# # #